When a Ford Puma is parked in a narrow underground car park, reversing using only the interior rear-view mirror leaves a blind spot beneath the rear bumper.
Adding a reversing camera solves this problem, but on this model, the choice of kit and wiring depend on the infotainment screen, model year and trim level. Before taking anything apart, you need to settle one question that determines everything else: keep the original screen or install a separate monitor.
Original or separate screen on the Ford Puma: the choice that determines everything
The Ford Puma comes with several infotainment screen configurations, depending on the trim level (Titanium, ST-Line, ST). An original screen with a camera input makes installation easier, but compatibility depends on the exact screen and wiring harness references. A generic kit labelled “Ford compatible” is not enough: check compatibility using the VIN or consult a specialist.
If the original screen accepts a video signal, you may need a dedicated interface or software activation for the image to appear automatically when reversing. Without this step, the camera may remain inactive or trigger an error message on the dashboard.
On entry-level trims equipped with a small screen that has no camera input, the most reliable solution is a separate monitor (a screen mounted on the rear-view mirror or a small monitor attached to the dashboard). This avoids any software compatibility issues, and the video connection uses a simple RCA cable. To better understand each step of the process, you can install a reversing camera on a Ford Puma by following a guide tailored to your exact configuration.

Ford Puma electrical connections: the reversing-light wire trap
Most generic guides recommend powering the camera directly from the reversing-light wire. On the Ford Puma, this advice needs some qualification. Some documented Ford interface kits explicitly advise against this connection: the reversing-light circuit’s delay can cause a black screen or an error message.
This happens because the Puma controls its rear lights through an electronic module. The power sent to the reversing light is not simply a constant 12 V as soon as reverse gear is engaged; it may be modulated or delayed. As a result, the camera receives an unstable power supply, causing the image to flicker or fail to appear altogether.
Which power supply to use
The kit manufacturer’s instructions take precedence over any general advice. Depending on the equipment, the correct power supply may come from a dedicated wire in the interface harness, a relay triggered by the reversing signal (without drawing power from it), or a separate switched 12 V source. Always check the wiring diagram for the specific vehicle before cutting or stripping a single wire.
- Disconnect the battery before working on the electrical system, even for a simple Scotchlok connection.
- Use a multimeter to confirm that the wire identified as the “reversing-light wire” is live only when reverse gear is engaged and the engine is running.
- Never connect the camera’s ground wire to a rusty or painted bodywork point: a poor ground connection can cause interference in the video image.
- If the kit includes an interface harness with an OBD or CAN connector, follow the manufacturer’s procedure exclusively and do not mix methods.
Routing the video cable in the Ford Puma
Running the cable between the camera (mounted near the rear number plate) and the screen at the front is the longest part of the installation. On the Puma, the tailgate wiring boot is the only route into the cabin from the boot.
Feed the video cable through the boot using a stiff guide wire (a straightened metal coat hanger or electrician’s fish tape). The cable must never be taut: the tailgate opens and closes thousands of times, and a cable under tension will eventually break within a few months.
Routing under the trim to the dashboard
Once inside the boot, run the cable along one side of the cabin under the side trim, passing beneath the rear and then front door sills. The Puma’s trim clips can be removed with a plastic tool (not a metal screwdriver, which will scratch the finish). Then route the cable to the dashboard via the driver’s-side A-pillar or beneath the glove box on the passenger side.
Secure every metre of cable with cable ties or adhesive clips to prevent vibration noise while driving. A loose cable touching sheet metal will rattle over every speed bump.

When to have a professional installer fit the camera
Installation is manageable for a careful DIYer on straightforward configurations (separate screen, basic wired kit, no CAN interface). However, several situations call for professional help.
- The original screen requires software activation or coding with a Ford diagnostic tool: without the right equipment, you cannot enable the camera input.
- The chosen kit uses an interface connected to the vehicle’s CAN network: a wiring error can generate fault codes in other systems (airbags, ABS, power steering).
- You see a black screen, an error message or a flickering image after the first test: rather than trying things at random, have the wiring harness diagnosed to avoid damaging the electronics.
The cost of professional installation varies depending on the kit’s complexity and the region, but it is preferable to corrective work after a short circuit or a persistent fault code.
Reversing cameras and safety: what the image doesn’t show
An aftermarket reversing camera provides visual assistance, not an obstacle detection system. The image does not measure distance or trigger an audible alert unless the kit explicitly includes parking sensors. Even a wide-angle field of view leaves blind spots on the sides.
So continue using your mirrors and visually check the area before reversing. The camera supplements these checks; it does not replace them. Aftermarket kit marketing tends to blur this distinction, but it remains crucial for everyday safety.
On the Ford Puma, installing a reversing camera is all about what you do before picking up a screwdriver: identify your screen, choose a verified compatible kit, and be prepared to call in a professional if the vehicle’s electronics are beyond your skill level. A properly installed system will last for years; a makeshift installation causes intermittent faults that you eventually learn to ignore—which is much the same as having no camera at all.



